BHD
JOD
KWD
LBP
OMR
QAR
SAR
USD
ifi Audio ZEN Phono MM/MC Phono Digital To Analog Converter
Fall in love with the extraordinarily dynamic 20V RMS fully Balanced output. Discover one of a kind Infrasonic filter intelligently separating record warps and bass requencies, which then cancels only the unwanted warps. Enjoy the exceptionally wide.
FEATURES:
- Analogue inputs: RCA.
- Analogue outputs: 4.4mm Balanced/RCA.
- Al infrasonic filter detects whether it is record warp or a real bass note (no DSP used).
- Multiple discrete ultra-low noise super regulators.
- Microcontroller controlled interface.
المنتجات المقترحة
فيزا وماستر كارد
منتجات شاهدها عملاء آخرون
معاينة موقع سماعة تك
تفاصيل المُنتج
- Input voltage: DC 5V/0.5A, AC 100 -240V, 50/60Hz
- Frequency Response:
- Balanced: 20Hz - 20kHz (±0.15dB)
- S-E: 10Hz - 100kHz (±0.4dB)
- Channel Separation: > 75dB (1kHz all modes)
- Max Output Voltage RMS:
- Balanced: 13.5V RMS 600R (<1% THD & N)
- S-E: 6.5V RMS 600R (<1% THD & N)
- Output Impedance:
- Balanced: 200 Ohm
- S-E: 100 Ohm
- SNR:
- MM (36dB ±1dB): 96dB (A-weighted) re 2V BAL/1V S-E
- MC High (48dB ±1dB) : 84dB (A-weighted) re 2V BAL/1V S-E
- MC Low (60dB ±1dB): 90dB (A-weighted) re 2V BAL/1V S-E
- MC V-Low (72dB ±1dB): 79dB (A-weighted) re 2V BAL/1V S-E
- Ein (equivalent input noise):
- 0.6nV | /Hz (unweighted) MC Low/MC V-Low -151dBV (A-weighted)
- 6.5nV | /Hz (unweighted) MM/MC High -130dBV (A-weighted)
- Total Harmonic Distortion:
- MM: <-110dB / 0.0003% re 2V BAL/1V S-E
- MC Low: <-80dB / 0.01% re 2V BAL/1V S-E
- MC V-Low: <-86dB / 0.005% re 2V BAL/1V S-E
- Power consumption: <1.8W
- Dimensions: 158 x 117 x 35 mm
- 6.2" x 4.6" x 1.4"
- Weight: 500 g (1.10 lbs)
- Warranty period: 1 year
ماذا في العلبة
- ifi Audio ZEN Phono MM/MC Phono Digital To Analog Converter
الفيديوهات
مواصفات المُصنع
ZEN Phono Front
- Power ON/OFF This is the power switch.
- MM input LED This is a MM input suitable for MM cartridges with the output voltage higher than 2mV. Please select Gain 1 at the rear.
- MC HIGH input LED This is a MC HIGH input suitable for MC cartridges with the output voltage less than or equal to 2mV. Please select Gain 2 at the rear.
- MC LOW input LED This is a MC LOW input suitable for MC cartridges with the output voltage less than or equal to 0.5mV. Please select Gain 3 at the rear.
- MC V-LOW input LED This is a MC V-LOW input suitable for MC cartridges with the output voltage less than or equal to 0.25mV. Please select Gain 4 at the rear.
- SUBSONIC Filter ON/OFF This is the SUBSONIC filter switch. The iFi-designed subsonic filter will intelligently detect whether a subsonic frequency is a warp or a bass note. It will eliminate the warps and let all the bass and mid-range frequencies pass through untouched. Therefore, it will not affect the sound quality.
ZEN Phono Back
Balanced 4.4mm analogue output This is an analogue output via 4.4mm > XLR or other balanced interconnects. You could use this for an active speaker or an amplifier. Tip: As ZEN Phono is balanced, this is the recommended output.
RCA analogue output This is an analogue output
.9. Ground This is the ZENPhono's ground, please connect it to the turntable's grounding wire.
RCA analogue input This is an analogue input.
Gain channel switch This button cycles between 4 gain levels:1. corresponds to MM(>2mV)2. corresponds to MCHIGH(≤2mV)3. corresponds to MCLOW(≤0.5mV)4. corresponds to MCV-LOW(≤0.25mV)Please adjust the gain channel switch in accordance with your preference and your turntable's specifications